BOYSEN®® Acrytex™ Primer B‑1705
BOYSEN®® Acrytex™ Primer is a primer for plain or textured Acrytex finishes. It is an acrylic solvent-based coating that forms a seamless, non-porous, watertight film that repels water and prevents seepage. It is noted for its excellent adhesion and long-term durability.
Technical Data
Principal Uses
As a primer for new exterior and interior masonry and wooden surfaces
Vehicle Type
Thermoplastic Acrylic
Dry Time
Touch: 30 minutes
Recoat: 2 hours
Recoat: 2 hours
*Measured at 25°C and 50% relative humidity
Density
(±0.05 kg/L)
1.35 kg/L
Theoretical Coverage
25-30 sq. m.
* per 4-Liters at 2.0-1.5 mils DFT
* per 4-Liters at 2.0-1.5 mils DFT
*Depending on surface texture and porosity
Tinting
Not applicable
Thinning
Solvent
BOYSEN®® Acrytex™ Reducer B‑1750
*If using brush or roller, use approximately 1-Liter of Acrytex Reducer B‑1750 per 4-Liter of Acrytex paint.
*If using brush or roller, use approximately 1-Liter of Acrytex Reducer B‑1750 per 4-Liter of Acrytex paint.
Clean-up
Solvent
BOYSEN®® Acrytex™ Reducer B‑1750
Packaging
4-Liters and 16-Liters
Application
By brush, roller, or spray
SURFACE PREPARATION
For Concrete
Allow new concrete to dry for 14-28 days under normal weather conditions before painting. Surface to be painted should be clean and dry, free from oil, grease, dust, dirt, contaminants, and all loose grit and mortar.
For Wooden Surfaces
Surface to be painted should be clean and dry, free from dust, dirt, and other foreign matter. Hammer all nails deep enough to apply putty. Sand rough wood until smooth and then dust off before painting.
Repainting
Any existing paint that is not Acrytex should be completely removed. Scrape off all loose, scaling, flaking, and peeling paint manually or by using BOYSEN®® Paint and Varnish Remover B‑141, as necessary. Wash surfaces clean and completely remove chemical residue. Let it dry.
For repainting concrete, use BOYSEN®® Chalk Blocker™ B‑7304 as surface conditioner if surface is chalky. In case of mildew infestation, treat with a bleach solution (1:3, laundry bleach to water, respectively) by swabbing or brushing. To ensure proper treatment, let stand for 24 hours before cleaning off residue. Let dry.
PAINTING SCHEDULE
Plain Finish
1. Prime bare substrate with BOYSEN®® Acrytex™ Primer B‑1705
2. Putty minor surface imperfections with BOYSEN®® Acrytex™ Cast B‑1711
3. Spot prime puttied areas with BOYSEN®® Acrytex™ Primer B‑1705
4. Finish with at least 2 coats of BOYSEN®® Acrytex™ Topcoat to desired sheen
2. Putty minor surface imperfections with BOYSEN®® Acrytex™ Cast B‑1711
3. Spot prime puttied areas with BOYSEN®® Acrytex™ Primer B‑1705
4. Finish with at least 2 coats of BOYSEN®® Acrytex™ Topcoat to desired sheen
Textured Finish
1. Prime bare substrate with BOYSEN®® Acrytex™ Primer B‑1705
2. Spray BOYSEN®® Acrytex™ Cast B‑1711 using a mortar gun. For a flattened texture, press Acrytex Cast B‑1711 using a plain wooden roller 10-15 minutes after spraying.
Note: Dampen wooden roller with water to prevent the roller from sticking to the cast.
3. Finish with at least 2 coats of BOYSEN®® Acrytex™ Topcoat to desired sheen
2. Spray BOYSEN®® Acrytex™ Cast B‑1711 using a mortar gun. For a flattened texture, press Acrytex Cast B‑1711 using a plain wooden roller 10-15 minutes after spraying.
Note: Dampen wooden roller with water to prevent the roller from sticking to the cast.
3. Finish with at least 2 coats of BOYSEN®® Acrytex™ Topcoat to desired sheen
For MSDS requests, please email technical@boysen.com.ph