BOYSEN®® Acrytex™ Sealer B‑1708
BOYSEN®® Acrytex™ Sealer is an acrylic solvent-based sealer intended for concrete surfaces situated in humid and cold climates.
Technical Data
Vehicle Type
Thermoplastic Acrylic
Dry Time
Touch: 20 minutes
Recoat: 1 hour
Recoat: 1 hour
*Measured at 25°C and 50% relative humidity
Density
(±0.05 kg/L)
0.90 kg/L
Theoretical Coverage
20 to 25 sq. m.
* per 4-Liters at 1.0-0.8 mils DFT
* per 4-Liters at 1.0-0.8 mils DFT
*Depending on surface texture and porosity
Tinting
Not applicable
Thinning
Solvent
BOYSEN®® Acrytex™ Reducer B‑1750
*If using brush or roller, use approximately 1-Liter of Acrytex Reducer B‑1750 per 4-Liter of Acrytex paint.
*If using brush or roller, use approximately 1-Liter of Acrytex Reducer B‑1750 per 4-Liter of Acrytex paint.
Clean-up
Solvent
BOYSEN®® Acrytex™ Reducer B‑1750
Packaging
4-Liters
Application
By brush, roller, or spray
SURFACE PREPARATION
For Concrete
Allow new concrete to dry for 14-28 days under normal weather conditions before painting. Surface to be painted should be clean and dry, free from oil, grease, dust, dirt, contaminants, and all loose grit and mortar.
For Wooden Surfaces
Surface to be painted should be clean and dry, free from dust, dirt, and other foreign matter. Hammer all nails deep enough to apply putty. Sand rough wood until smooth and then dust off before painting.
Repainting
Any existing paint that is not Acrytex should be completely removed. Scrape off all loose, scaling, flaking, and peeling paint manually or by using BOYSEN®® Paint and Varnish Remover B‑141, as necessary. Wash surfaces clean and completely remove chemical residue. Let it dry.
For repainting concrete, use BOYSEN®® Chalk Blocker™ B‑7304 as surface conditioner if surface is chalky. In case of mildew infestation, treat with a bleach solution (1:3, laundry bleach to water, respectively) by swabbing or brushing. To ensure proper treatment, let stand for 24 hours before cleaning off residue. Let dry.
PAINTING SCHEDULE
Plain Finish
1. Apply BOYSEN®® Acrytex™ Sealer B‑1708 directly onto bare concrete substrate
2. Prime resulting surface with BOYSEN®® Acrytex™ Primer B‑1705
3. Putty minor surface imperfections with BOYSEN®® Acrytex™ Cast B‑1711
4. Spot prime puttied areas with BOYSEN®® Acrytex™ Primer B‑1705
5. Finish with at least 2 coats of BOYSEN®® Acrytex™ Topcoat to desired sheen
2. Prime resulting surface with BOYSEN®® Acrytex™ Primer B‑1705
3. Putty minor surface imperfections with BOYSEN®® Acrytex™ Cast B‑1711
4. Spot prime puttied areas with BOYSEN®® Acrytex™ Primer B‑1705
5. Finish with at least 2 coats of BOYSEN®® Acrytex™ Topcoat to desired sheen
Textured Finish
1. Apply BOYSEN®® Acrytex™ Sealer B‑1708 directly onto bare concrete substrate.
2. Prime resulting surface with BOYSEN®® Acrytex™ Primer B‑1705
3. Spray BOYSEN®® Acrytex™ Cast B‑1711 using a mortar gun. For a flattened texture, press Acrytex Cast B‑1711 using a plain wooden roller 10-15 minutes after spraying.
Note: Dampen wooden roller with water to prevent the roller from sticking to the cast.
4. Finish with at least 2 coats of BOYSEN®® Acrytex™ Topcoat to desired sheen
2. Prime resulting surface with BOYSEN®® Acrytex™ Primer B‑1705
3. Spray BOYSEN®® Acrytex™ Cast B‑1711 using a mortar gun. For a flattened texture, press Acrytex Cast B‑1711 using a plain wooden roller 10-15 minutes after spraying.
Note: Dampen wooden roller with water to prevent the roller from sticking to the cast.
4. Finish with at least 2 coats of BOYSEN®® Acrytex™ Topcoat to desired sheen
For MSDS requests, please email technical@boysen.com.ph