BOYSEN®® Quick Drying Enamel

BOYSEN®® Quick Drying Enamel is an alkyd type paint that provides substantial durability while still being a fast drying paint. It is formulated to give a tough and beautiful finish on wood and metal surfaces. Its superior hiding properties, combined with an exceptionally high gloss level, leads to an excellent, long-lasting finish.
Download Brochure

Technical Data

Principal Uses

Ideal for interior and exterior wood and metal surfaces

Vehicle Type

Alkyd Resin

Finish

Gloss

Dry Time

Touch: 5 hours
Recoat: 8-12 hours
Full cure: 3 days
*Measured at 25°C and 50% relative humidity

Density
(±0.05 kg/L)

1.11 kg/L

Theoretical Coverage

30-35 sq. m.
* per 4-Liters at 2.0-1.8 DFT
*Depending on surface texture and porosity

Tinting

Will accept BOYSEN®® Oil Tinting Colors at a maximum level of ¼ Liter per 4-Liter can. Take note that B‑2319 Hansa Yellow and B‑2315 Bulletin Red are for interior painting only.

Thinning
Solvent

Thin with not more than 1-Liter of BOYSEN®® Paint Thinner B‑0340 per 4-Liter can of BOYSEN®® alkyd enamel products.

Clean-up
Solvent

BOYSEN®® Paint Thinner B‑0340

Packaging

¼ Liter, 1-Liter, and 4-Liters
(available in 16-Liters for B‑600 White)

Application

By brush or roller

SURFACE PREPARATION

Wooden Surfaces

Surface to be painted should be clean and dry, free from dust, dirt, and other foreign matter. Hammer all nails deep enough to apply putty. Sand rough wood until smooth and then dust off before painting.
For repainting, scrape off all loose, scaling, flaking, and peeling paint manually or by using BOYSEN®® Paint and Varnish Remover B‑141, as necessary. Wash surfaces clean and completely remove chemical residue. Let it dry. Prime with BOYSEN®® Flatwall Enamel B‑800 before recoating.

Metal Surfaces

Wipe the surface with a rag soaked in paint thinner to remove grease, oil, wax and other foreign matter. For new galvanized surfaces, etch the surface by applying 10% BOYSEN®® Metal Etching Solution B‑71 (Dilute 1 part of B‑71 to 9 parts water). Rinse with water and dry immediately.
Unpainted galvanized surfaces that have been exposed for 6 months or more need not be etched.
For recoating pre-painted galvanized surfaces in good condition, sand lightly then wipe the surface with a clean rag before applying paint. Remove all loose paint film to sound surface. Spot prime bare substrate.
For corroded galvanized surfaces, remove rust by wire brushing and use BOYSEN®® Metal Etching Solution B‑71. Let it stay for 10-15 minutes. Be sure to remove all remaining residue. Immediately prime after drying.

PAINTING SCHEDULE

Wooden Surfaces

Primer:
BOYSEN®® Flatwall Enamel B‑800
Putty:
BOYSEN®® Plasolux Glazing Putty B‑311
2nd & 3rd coat:
BOYSEN®® Quick Drying Enamel (any desired color)

Metal Surfaces

Primer:
BOYSEN®® Red Oxide Metal Primer B‑310 or BOYSEN®® Rust-Off™ B‑330
2nd & 3rd coat:
BOYSEN®® Quick Drying Enamel (any desired color)

Colors

B‑600
White
B‑621
Ivory
B‑630
Silver Gray
B‑631
Medium Gray
B‑640
Royal Blue
B‑642
Sky Blue
B‑647
Delft Blue
B‑650
Nile Green
B‑651
Dark Green
B‑656
Jade Green
B‑658
Emerald Green
B‑661
Lemon Yellow
B‑665
Caterpillar Yellow
B‑670
Bright Red
B‑671
International Red
B‑673
Maroon
B‑676
Orange
B‑680
Chocolate Brown
B‑681
Mahogany
B‑683
Caramel Brown
B‑685
Sammy Brown
B‑690
Black
* For technical reasons connected with color reproduction in print and paint manufacturing,
these colors may not exactly match actual paint color.
For MSDS requests, please email technical@boysen.com.ph